Exactly How to Remove and Also Change a Bathtub
Exactly How to Remove and Also Change a Bathtub
Blog Article
Here in the next paragraph yow will discover additional really good details with regards to Tools You Need to Install a New Bathtub .
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the project can move quickly; if you have to open up a wall surface to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the task as well as are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you might require an expert plumber to make tube connections.
This article will certainly aid you mount a brand-new tub in your restroom if you have actually currently gotten a brand-new bathtub and also do not need to change the arrangement of your previous water pipelines.
Your tools as well as material list must make up the following:
Preparing for the Installation
To start with, the sustaining frame provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop pressure on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning during this procedure. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Using both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bathtub till the level checks out level.
To mount taps, fit the bottom of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as check all joints and also new pipework for leaks and also tighten them if needed. Fill the bath tub as well as also examine the overflow outlet and the regular electrical outlet for leaks.
Finally, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub needs to wait up until the bathtub has actually been used at the very least once as this will certainly settle it right into its final setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the faucet in position with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break a stiff seal, triggering the water to penetrate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealant can fracture rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that section was smart. If you liked our post please don't forget to share it. Many thanks for your time. Don't forget to pay a visit to our website back soon.
Make An Appointment
Report this page